Phil Wood

Axle conversion kits for Phil Wood track hubs.

The Longest lasting square taper bottom bracket out there. Heat-treated stainless steel spindle bottom bracket is offered with an aluminium alloy cartridge and Phil Wood PWX03 bearings for maximum durability and minimum flex. Available with Campy (ISO) or Shimano (JIS) tapers and in a variety of lengths.
Lengths not listed below can be special ordered, Ti axle options available – please contact us for more details. All bottom bracket sets require the Phil Wood bottom bracket cups and installation tool.

Designed to help protect your Phil Wood bottom bracket cups from getting dust, dirt and mud that accumulate in and around the bottom bracket cup splines.
They are designed with a drain opening to allow any moisture between the bearing and the mudguard to vent out. They will fit onto any Phil Wood square tapered bottom bracket cup sets. Each set of mudguards comes with 4 rubber o-rings (two pre-installed and two replacement).

Designed to help protect your Phil Wood bottom bracket cups from getting dust, dirt and mud that accumulate in and around the bottom bracket cup splines.
They are designed with a drain opening to allow any moisture between the bearing and the mudguard to vent out. They will fit onto any Phil Wood square tapered bottom bracket cup sets. Each set of mudguards comes with 4 rubber o-rings (two pre-installed and two replacement).

Phil Wood threaded bottom bracket cups will fit onto any of Phil Wood bottom bracket cartridges produced since 1971. They are an interference fit with the bottom bracket, and will require Phil Wood bottom bracket installation tool to install. Cups will ship with a small tube of thread retaining compound (which must be used during assembly).
Cutting taps used to produce the bottom bracket thread in cups leave microscopic hairs and cracks in the thread form. Thread in PW cups is hand polish to all but eliminate galling between cups and the bottom bracket thread.

Phil Wood threaded bottom bracket cups will fit onto any of Phil Wood bottom bracket cartridges produced since 1971. They are an interference fit with the bottom bracket, and will require Phil Wood bottom bracket installation tool to install. Cups will ship with a small tube of thread retaining compound (which must be used during assembly).
Cutting taps used to produce the bottom bracket thread in cups leave microscopic hairs and cracks in the thread form. Thread in PW cups is hand polish to all but eliminate galling between cups and the bottom bracket thread.

Phil Wood threaded bottom bracket cups will fit onto any of Phil Wood bottom bracket cartridges produced since 1971. They are an interference fit with the bottom bracket, and will require Phil Wood bottom bracket installation tool to install. Cups will ship with a small tube of thread retaining compound (which must be used during assembly).
Cutting taps used to produce the bottom bracket thread in cups leave microscopic hairs and cracks in the thread form. Thread in PW cups is hand polish to all but eliminate galling between cups and the bottom bracket thread.

Phil Wood threaded bottom bracket cups will fit onto any of Phil Wood bottom bracket cartridges produced since 1971. They are an interference fit with the bottom bracket, and will require Phil Wood bottom bracket installation tool to install. Cups will ship with a small tube of thread retaining compound (which must be used during assembly).
Cutting taps used to produce the bottom bracket thread in cups leave microscopic hairs and cracks in the thread form. Thread in PW cups is hand polish to all but eliminate galling between cups and the bottom bracket thread.

Phil Wood is credited with pioneering the first modern production sealed bearing cycling components.

Standard bearings are 100% filled with Phil Waterproof Grease to ensure maximum durability. Any of bearings with an “x” in the part number have seals that are as good or better than those found in the highest quality submersible motor and pump bearings.

Bearings can be used to replace bearings found in many other cycling manufacturer’s parts. Please see the descriptions of the part numbers to determine which bearings may best meet your needs.

A lighter lubricant than Phil Wood Tenacious Oil, Bio-Lube is created using all-natural ingredients and works as a fair-weather lubricant, as well as an all-purpose household lubricant.

Photos for illustrative purposes only, colour of the bottle may vary.

Portable square taper bottom bracket cup installation tool which requires using a 22mm closed end wrench to use. This tool is unchanged since its original release by us is in 1971.

One recommended for British Cups and two required for Italian Cups.

Phil Wood's professional bottom bracket wrench. Same high quality built, but with a handle for better leverage.

Built to last, like everything from Phil Wood, comes the specifically designed Brompton front hub.

Over-locknut dimension of 74mm, precision sealed bearings and a bolt-on stainless steel axle. This is “THE” hub you are looking for if looking to upgrade your build.

Built to last, like everything from Phil Wood, comes the specifically designed Brompton front hub.

Over-locknut dimension of 74mm, precision sealed bearings and a bolt-on stainless steel axle. This is “THE” hub you are looking for if looking to upgrade your build.

Chrome Dome – high quality, heavy duty axle bolt washers (supplied as a pair).

Replacement axle for Phil Wood front track hubs.

These are replacement bolts for front track hubs. These have a thread pitch of M8 x 1.25 x 40mm. Sold in pairs. Includes washers and O-Rings.

Phil Wood hand cleaner is extremely effective. It’s meant to be used on dry hands, worked in, then rinsed off. Just a small amount will remove stubborn grease, oil, and dirt.

Used by bicycle and automotive mechanics, it is effective and “clean” smelling. No animals were used for testing and no animal products are used in production of this hand cleaner.

The ISO front hub has a larger flange than our high-flange track hub, making it as strong as an Ox!

Designed for heavy and/or dead aggressive riders. Treat it mean and it’ll stay keen.

Phil Wood’s stainless steel ISO track cogs are available in 1/8″ only and are designed to be used with Phil Wood ISO hubs or any ISO fitting.

Phil Wood's commitment to the best materials, precision machining, and their extensive heat treating process provides you with a world class track cog that's strong, long lasting, corrosion resistant, and a component you'll be proud to have on your bike.

This is a 3 oz. (85g) tube of Phil Wood Water Proof Grease for those who do a lot of their own work around their shop/garage.

Lil’ Phil Grease Gun comes with: one 3oz Lil’ Phil grease cartridge, a one-piece solid extension, and a needle nose adapter.

Italian threading lockring for Phil Woods track hubs.

Phil Portable Grease Gun with Waterproof grease. perfect for greasing all moving parts of your bike, especially those bearings. Phil's waterproof grease is tested and has achieved the Premium Lubricant Classification by all major bearing manufacturers. Phil's grease is a standard in the industry, used by manufacturers and bike shops all around the world. It's a great addition to your home shop too.

Phil Wood Waterproof Grease is used to pack all our Phil Spec’d bearings for maximum durability. It is tested and has achieved the “premium” lubricant classification by all major bearing manufacturers worldwide.

Phil quick release skewers are machined in-house and manufactured from US produced 6061 aluminium and stainless steel for uncompromising strength and reliability.

Each lever and adjusting nut is then finished off with engraved and hand painted "Phil" and "P".

These are replacement bolts for rear track hubs. These have a thread pitch of M8 x 1.25 x 40mm. Sold in pairs.

Phil Wood Tenacious Oil is used for ultimate protection and durability for components that have movement with metal-to-metal contact.

Photos for illustrative purposes only, colour of the bottle may vary.